Effective mold cleaning with Step #1 – Mold Cleaner
Mold Hydrogen Peroxide Solution
Concentrated Mold Cleaner Advantages:
- No Chlorine Bleach
- Environmentally Safe
- Commercial Professional Strength
- Oxygen Powered Peroxide Mold Cleaner
- Meets Or Exceeds Green Seal & DFE Compliance Standards
- 1:1 Concentrate doubles the volume.
Hydrogen Peroxide: Harness the power of Oxygen in a Mold Cleaning product
MoldSTAT Commercial #1 is a concentrated PerOxy Cling mold cleaner specially designed to cling to mold stains on vertical surfaces while addressing the environmental, safety and health concerns facing today’s housekeeper and facility maintenance professional.
Clinging to surfaces longer improves mold removal results.
Strong highly fortified hydrogen peroxide mold and mildew cleaning formulation is color safe . Hydrogen Peroxide releases Oxygen Mold Cleaning power.
Oxidizes soils, mold stains and bacteria while eliminating associated odors leaving a fresh pleasant smell
Concentrated and color safe!
Mold Cleaner PerOxy Kling concentrate contains no acids, amonia, phosphates!
Powered by hydrogen peroxide, H2O2, Per Oxy Kling releases Oxygen as a Mold Cleaner
There are no caustics, butyl or glycol ethers,
Step #1 Mold Cleaner – PerOxy Kling is a powerful Mold Cleaner without silicones, chelating agents or dyes.
Versatile Mold Cleaning
Oxygen powered MoldSTAT PerOxy Kling Cleaner for mold stain removal on walls, floors, tile and grout, carpets, stainless steel, chrome, porcelain, concrete.
Exterior housing surfaces and roofs are safe for Oxygen Mold Cleaner PerOxy Kling.
Clinging Property Allows longer saturation with Active Ingredients
Clean, Kill and Prevent Mold
Mold Cleaners remove surface mold, but do not kill mold. After Cleaning mold with MoldSTAT PerOxy Kling you will be ready to kill the mold. Choose between two Mold Killing Products:
- MoldSTAT Plus mold killer – Concentrated,non-bleach EPA registered mold and mildew killing product
- MoldSTAT Protector – concentrated mold removal non-bleach EPA registered to kill & prevent mold
How to use Step #1 Mold Cleaner Concentrate on:
HARD SURFACES
Mix 1:1 with water and spray on surface; agitate with cloth or brush if needed.
Rinse with water.
Wipe dry with clean cloth or paper towel.
KITCHEN AND HOUSEHOLD SURFACES
Mix 1:1 with water and spray on stain and rub in gently.
For tough stains, scrub with sponge.
Rinse thoroughly with water and allow to dry.
TILE AND GROUT
Mix 1:1 with water and spray on surface of tile and/or grout.
Allow a few minutes of dwell time on heavily soiled surfaces.
Agitate with a nylon brush to remove heavy soil deposits.
Rinse with water to remove solution.
Tile and grout will be sparkling clean and residue-free.
CARPETS AND UPHOLSTERY
Before using, always test for colorfastness in an inconspicuous area.
Remove all loose dirt from area to be cleaned.
Blot, if wet, soiled area with clean, color safe cloth or paper towel.
Spray soiled area and allow to penetrate stain for 3-5 minutes.
Blot with a clean, damp, colorfast cloth.
Rinse cloth and repeat until clean.
For carpets, vacuum when dry.
Do not use on leather or silk.
MOLD AND MILDEW:
Mix 1:1 with water and spray directly on mold and mildew.
Allow to remain on treated area for 3-5 minutes.
Rinse.
For heavily contaminated areas light scrubbing may be required.
RESTROOMS AND SHOWERS
For porcelain, fiberglass and stainless steel associated with restroom fixtures (urinals, sinks, tubs, etc.) Mix 1:1 with water and apply directly on surface and rub with sponge or cloth.
Rinse with clean water and allow to air dry or wipe dry with a clean cloth.
LAUNDRY
Remove any stain accumulation.
Saturate stained area, rub into fabric and let stand for 5-10 minutes, then wash as usual.
For cleaning large areas
SUCH AS: Concrete, floors, roofs, fences, decks or exterior building walls, one apply with a pump-sprayer or bucket and mop using a 1:1 dilution ratio with water.
Apply liberally and let dwell for 5-10 minutes.
Scrub heavily contaminated areas, then rinse.
Larry T –
Was given some by a neighbor who recommended I try it on a mold that was persistent to other products.
It worked very well but I needed more to finish the cleaning. I looked it up online and I felt the price was reasonable and so I ordered Peroxy Kling Multi Surface Cleaner.
I have used the product and I am extremely happy with the results on my vinyl siding that had become unsightly.
I would recommend Peroxy Kling Multi Surface Cleaner very highly.
The customer service was excellent, price was reasonable, and the product certainly did the job! Will certainly use the product in the future!
Kelsey from Lehigh, PA –
My boyfriend and I bought a foreclosed home with a serious black mold problem in the crawls space and basement. The mold was caused by a flooding related sump pump failure. Instead of spending thousands of dollars to have someone else clean it, we found your mold removal products and advice on Cleaner Today’s website and decided to do it ourselves. We applied the PeroxyKling three times to the entire basement (both foundation and concrete cinder block), and then we used your Fogmaster Jr. to apply the MoldStat Plus (three times, to be sure).
There was more than enough product for the applications, and now that we have cleaned and fogged the entire house, the odor and mold is gone, and we can move in safely (Air tests we showing 22,000 spores per square meter *before* the MoldStat, and we plan to have the air tested again to keep on record that we have remediated the mold).
I have severe allergies, and go into anaphylaxis from mold. The fact that I can breathe easily and have no reaction is proof alone that moldstat plus worked!
We can’t thank you enough, and now recommend your product to anyone who has a mold problem.
THANK YOU!!!
Mark –
How do you use it on wood? 2×4’s?
Resident Guru –
MoldSTAT Step 1, ( previously called Peroxy Kling ) should be mixed 1:1 with water into a sprayer, then applied in a light coat on wood, structural components ( 2 x 4 etc ) and allowed to soak in… to loosen the ‘gunk’ then wiped down..
To Kill mold, follow with MoldSTAT Step 2 ( previously called MoldSTAT Plus )